UGREEN Official Site

UGREEN MagFlow 2-in-1 Charger Setup: 25W Magnetic Charging Tips

UGREEN MagFlow 2-in-1 Charger Setup: 25W Magnetic Charging Tips

By UGREEN Official Site | Published: 2026-11-04

Category: Anleitungen

Set up your UGREEN MagFlow 2-in-1 Magnetic Wireless Charger 25W for a tidy desk. Follow these steps for stable magnetic alignment and faster Qi2 charging.

Quick answer

Place the UGREEN MagFlow 2-in-1 Magnetic Wireless Charger 25W on a flat, stable surface near a power outlet, connect it to a compatible USB-C power adapter, and align your phone and second device with the magnetic guides. For best results, use a MagSafe-compatible case or no case at all.

Why placement and power matter for 25W magnetic charging

The MagFlow 2-in-1 delivers up to 25W to compatible devices, but actual speed depends on the power adapter and the device’s charging profile. A weak adapter or a thick case can reduce performance even when the charger is correctly positioned.

Magnetic alignment helps maintain a secure connection, but it is not a substitute for proper placement. Keep the charger away from metal objects and credit cards to avoid interference.

When a 2-in-1 charger is the right fit

This charger suits people who want to power a phone and a second device, such as earbuds, from one spot. If you need to charge two phones at full speed simultaneously, check the power distribution—the 25W output may be shared between devices depending on the model.

For travel, a foldable design may be more convenient; the MagFlow 2-in-1 is best kept on a desk or nightstand.

Step-by-step setup for the MagFlow 2-in-1

  1. Choose a stable, flat surface: Place the charger on a desk or nightstand where it won’t be knocked over. Avoid soft or uneven surfaces that can prevent the magnetic mounts from sitting flat. Common mistake: placing it on a bed or cushion, which can cause misalignment. Check that the charger sits level and does not wobble.
  2. Connect to a compatible power adapter: Use a USB-C power adapter that supports the charger’s required input. The catalog does not specify the exact adapter wattage, so refer to the included manual or product page. A underpowered adapter may slow charging. Common mistake: using a low-power phone charger. If charging seems slow, try a higher-wattage adapter.
  3. Align your phone with the magnetic guide: Bring your phone close to the main charging pad; the magnets will pull it into place. For MagSafe-compatible iPhones, center the phone over the pad. For other Qi2 devices, follow the manufacturer’s alignment guide. Common mistake: forcing the phone off-center, which weakens the magnetic hold. You should feel a gentle snap when the phone is correctly aligned.
  4. Place your second device on the secondary pad: Set earbuds or another compatible device on the second charging area. Make sure it is centered and not overlapping the phone. Common mistake: stacking devices or placing them too close to the edge. Both devices should start charging; check their screens for confirmation.
  5. Remove thick cases and metal accessories: Magnetic charging works best without a case or with a MagSafe-compatible case. Cases thicker than 3mm, wallets with magnets, or metal plates can block the magnetic field. Common mistake: leaving a pop socket or card holder attached. If charging does not start, remove the case and try again.
  6. Check for interference and heat: Keep the charger away from other wireless chargers, metal objects, and direct sunlight. Some warmth is normal, but if the charger or phone becomes hot, move it to a cooler spot. Common mistake: placing it near a laptop vent or radiator. After 10 minutes, the charger should be warm but not uncomfortable to touch.

Product facts

Shop Related Products

UGREEN MagFlow 2-in-1 Magnetischer Wireless Charger 25W

UGREEN MagFlow 2-in-1 Magnetischer Wireless Charger 25W

$897.69 $1301.00

Shop Now